Using Queen Excluders Correctly in a Hive

A queen excluder can be the difference between clean, straightforward honey harvesting and finding brood across every super at the height of the flow. But using queen excluders correctly is not simply a matter of placing one above the brood box and walking away. Timing, colony strength, hive layout and regular inspections all affect whether the bees use the supers well.

Some beekeepers use an excluder as standard; others avoid them after seeing a colony hesitate below the super. Both experiences can be valid. A queen excluder is a useful management tool, but it cannot compensate for a weak colony, insufficient space or a queen already laying above it.

What a queen excluder is for

A queen excluder is a grid that allows workers to pass through while preventing the larger queen from entering the boxes above. Its main job is to confine brood to the brood chamber, leaving the supers for honey stores.

For most beekeepers, that means frames in the honey supers are easier to extract, clearer to assess and free from developing brood. It is particularly helpful when you want to remove supers promptly for extraction, sell cut comb, or keep a more consistent honey crop. It can also make swarm-control inspections easier to organise because the queen is known to be below the excluder.

The grid will not stop drones. Drones are generally too large to pass through it, so they remain below. This is normal and is one reason a colony needs adequate room and ventilation in the brood area during busy periods.

The phrase “honey excluder” is sometimes used critically because workers can be slow to cross a poorly fitted or badly timed excluder. The issue is usually not the excluder alone. Bees need a strong reason and a clear route to move upwards.

When to put on a queen excluder

Fit the excluder when the colony is building strongly and there is a genuine need for super space. In much of the UK, this may be during spring build-up or shortly before the first reliable nectar flow, but local weather and forage matter more than the calendar. A warm April in Lincolnshire can look very different from a cold, wet one only a few years later.

Before adding it, make sure the brood box is not congested. The colony should cover a good number of frames with bees, have a laying queen and show signs that it can make use of a super. Adding several empty supers above an excluder to a modest colony can discourage upward movement and leave the brood nest crowded below.

If you are supering for a rapid flow, one drawn super directly above the excluder is often easier for bees to accept than a box entirely filled with foundation. Drawn comb carries the scent and structure of a usable space. Once bees are working it, further supers can be added as required.

There are exceptions. During some swarm-control methods, an excluder may be part of a specific arrangement rather than a normal honey-production set-up. Follow the details of the method closely. An excluder used in the wrong position can trap the queen away from sufficient laying space or leave brood where you do not expect it.

How to fit an excluder properly

Place the queen excluder flat between the brood box and the first honey super. Check that it sits squarely on the hive and is not bowed, cracked or blocked with old wax and propolis. A warped plastic grid creates awkward gaps and poor bee space; a damaged metal grid may leave a route wide enough for a small queen.

The orientation of some framed excluders matters. If there are supporting bars or a raised edge, follow the manufacturer’s intended way up so the bees have a clear passage. There is no benefit in creating a tight, obstructed entrance to the supers.

Avoid putting the excluder over a box with exposed brace comb or lumpy frame top-bars. Scrape off excess wax first so the surfaces meet evenly. A neat hive interface is not about appearance alone – it helps the colony move through the hive and reduces places where bees can build comb in inconvenient positions.

If the colony has not used supers before, encourage them rather than forcing the issue. A super containing a few frames of drawn comb can help. Some beekeepers temporarily place the queen excluder above a super for a short period, allowing the queen to lay in that box and establish bees there, then move it beneath the super once she is back below. This can work, but it needs careful timing so brood is not left in honey supers when you want to harvest.

Do not routinely shake bees through an excluder or repeatedly disturb the colony to make them cross it. Give them appropriate space, a usable comb and a worthwhile nectar flow instead.

Check where the queen is before you rely on it

The most common problem is fitting an excluder while the queen is already in a super. Once the grid is in place, she cannot return to the brood box. She may continue laying above it while the lower brood box becomes increasingly queenless.

Whenever practical, locate the queen before fitting the excluder. If you do not see her, look for fresh eggs and very young larvae in the brood box. Their presence tells you she was there within the previous few days, although it is not absolute proof that she is still there at that moment.

At the next inspection, check both sides of the excluder. Eggs and young larvae above it mean the queen is above, or was above recently. Remove the excluder temporarily, find and return the queen to the brood box, then replace it. If there is sealed brood in a super but no fresh brood, the queen may have been there earlier and has since moved down. That brood can emerge in up to 21 days from the egg stage, so plan your harvest around it rather than extracting frames containing brood.

Why bees may ignore the supers

When bees gather under the excluder instead of working above it, inspect the colony rather than blaming the grid immediately. The colony may be too small, the weather may have stopped forage, or the brood box may contain enough unused space that there is no pressure to expand upwards.

Foundation-only supers can also be slower to draw, especially during a poor flow. A strong colony will often draw foundation readily when nectar is coming in, but it may not do so in cool weather or during a forage gap. In that situation, adding more boxes rarely helps.

A clogged excluder is another simple cause. Propolis, wax bridges and debris reduce the openings available to workers. Lift it at inspections and clean it when needed. Plastic excluders benefit from gentle scraping; take care not to enlarge or distort the slots.

It also depends on the queen. A very slim virgin queen may pass through some grids, while an old or poorly fed queen may struggle more than expected. If you repeatedly find a marked, mated queen above a sound excluder, inspect it for damage and consider replacing it.

Choosing the right approach for your hive

Metal wire excluders are durable and easy to clean, while plastic versions are lighter and often less expensive. Framed excluders can be easier to handle and may maintain better spacing, particularly on hives where box edges are uneven. No material is automatically best. Choose one that fits your hive type accurately and remains flat in use.

For a brood-and-a-half or double-brood colony, the excluder normally goes above all boxes intended for brood. Restricting the queen to only one box when she needs two can increase crowding and contribute to swarming. Conversely, leaving a large brood area beneath the excluder can reduce the urgency for bees to store honey overhead. Management should follow the colony’s size and the season.

Make the excluder part of each inspection

During the active season, check that bees are using the first super, that the brood nest has enough room, and that the queen remains where you expect her to be. If the super stays untouched for more than a couple of inspections during a flow, investigate. Remove burr comb, confirm the colony is queenright and strong, and consider whether drawn comb would help.

At the end of the honey season, remove the excluder once the supers are off. Leaving it on through winter can restrict the cluster as it moves upwards to reach stores. Wintering bees need clear access through the hive, not a grid between them and their food.

Used well, a queen excluder is neither essential in every hive nor something to fear. Let the colony’s strength, the available forage and your harvest plans guide the decision. The best result is a hive with enough room to thrive and honey supers that are ready when you are.

Leave a Comment

Your email address will not be published. Required fields are marked *

Shopping Basket
Scroll to Top